Sürdürülebilir Kalkınma Amaçları
Yazarlar
Yayınlar
- MakaleAçık Erişim2023Scopus SJRQ2Investigation of organic and inorganic matters removal from tannery wastewater using iron plate electrode by electrocoagulation process
Bingül, Züleyha; Irdemez, Şahset; Kul, Sinan; Ekmekyapar Torun, Fatma; Demircioğlu, Nuhi
In this study, COD, turbidity, total nitrogen, phosphate, sulphate, oil-grease and chromium removals from wastewaters taken from a local tannery using the electrocoagulation process were examined and the most suitable parameters for the electrocoagulation system were tried to be determined. Soluble iron plate electrodes were used as electrodes in the experiments. As a result of the studies carried out, the most suitable initial pH in uncontrolled pH was determined as pH = 4 and for controlled pH as pH = 5. In studies, the most suitable current density for iron electrodes was determined as 1.2 mA cm−2. Even if the increase in current density increased the amount of dissolved Fe, it negatively affected the removal efficiency. In addition, the turbidity of the wastewater was removed in 30 minutes, phosphate in 20 minutes and chromium in 15 minutes by 100%. During 60 minutes of operation, while 62.91% of TN, 87.8% of oil-grease were removed, sulphate was removed at the rate of 54.78%. In the studies, 1st and 2nd order kinetic equations for COD removal were examined and it was determined that removal kinetic is more suitable for 2nd order kinetics.
AtıfScopus7WoS4
İncele - MakaleAçık Erişim2021Scopus SJRQ3A novel weighted mean-squared error optimization model to obtain optimal conditions of adsorption factors for a lead removal process
Özdemir, Akın; Teke, Çağatay; Serencam, Hüseyin; Uçurum, Metin; Gündoğdu, Ali
Lead (Pb) removal process from wastewater is an important issue to prevent health problems for people. For this particular purpose, a low-cost adsorbent may be beneficial for improving the adsorption capacity for the Pb removal process. The aims of this paper are four-fold. First of all, a D-optimal experimental design was selected to reduce experimental runs and its cost. Second, the effect of four adsorption design factors, stirring speed (rpm), adsorbent dosage (g), pH level, and initial metal concentration (ppm), was examined. Also, the yellow natural stone, which is from Bayburt, Turkey, was used as a cheap adsorbent for the Pb removal process from the solu-tion. Third, a novel weighted mean-squared error optimization model was developed to obtain optimal adsorption levels for adsorption factors. Besides, a verification study was conducted to verify the results of the adsorption experiment. Finally, the lead (Pb(II)) removal capacity of the yellow Bayburt stone was obtained to be 46.031 mg/g, and the results of the experiment from the proposed methodology showed a good performance for the removal study.
- MakaleYalnız künye2020Scopus SJRQ1Azo dye-functionalized magnetic Fe3O4/polyacrylic acid nanoadsorbent for removal of lead (II) ions
Sadak, Omer; Hackney, Robert; Sundramoorthy, Ashok K.; Yilmaz, Galip; Gunasekaran, Sundaram
We report the fabrication of a nanoadsorbent for the removal of heavy metals. The nanoadsorbent is comprised of ferric oxide (Fe3O4) magnetic nanoparticles (MNPs) covalently conjugated with polyacrylic acid (PAA) and further functionalized with an azo dye (Congo red, CR) using carbodiimide. This Fe3O4 core and PAA-CR shell system (MNP/PAA-CR) exhibited binding affinity towards various cations (Pb2+, Fe2+, Fe3+, Cd2+, and Cu2+) at room temperature. Using MNP/PAA-CR we studied its heavy metal removal effectiveness and kinetics targeting Pb2+ under various reactions conditions including time and pH. The Pb2+ removal efficiency and adsorption capacity were maximal at pH 6.5 and 45 min of reaction time, and the Pb2+ adsorption kinetics better fit a pseudo second-order model than a first-order model. The adsorption of Pb2+ by MNP/PAA-CR was also investigated by the so-called Langmuir and Freundlich isotherms, and the Langmuir isotherm predicted a maximum absorption of 195.3 mg.g-1. Our results further indicated that MNP/PAA-CR is potentially reusable after desorption of the adsorbed metal with only small decline in adsorption ability over five consecutive cycles of regeneration.
AtıfScopus26OpenAlex17İncele