Sürdürülebilir Kalkınma Amaçları

• 2
• 2

• MakaleAçık Erişim2023Scopus SJRQ2/r/bayburt/11804
  Investigation of organic and inorganic matters removal from tannery wastewater using iron plate electrode by electrocoagulation process

  Bingül, Züleyha; Irdemez, Şahset; Kul, Sinan; Ekmekyapar Torun, Fatma; Demircioğlu, Nuhi

  In this study, COD, turbidity, total nitrogen, phosphate, sulphate, oil-grease and chromium removals from wastewaters taken from a local tannery using the electrocoagulation process were examined and the most suitable parameters for the electrocoagulation system were tried to be determined. Soluble iron plate electrodes were used as electrodes in the experiments. As a result of the studies carried out, the most suitable initial pH in uncontrolled pH was determined as pH = 4 and for controlled pH as pH = 5. In studies, the most suitable current density for iron electrodes was determined as 1.2 mA cm−2. Even if the increase in current density increased the amount of dissolved Fe, it negatively affected the removal efficiency. In addition, the turbidity of the wastewater was removed in 30 minutes, phosphate in 20 minutes and chromium in 15 minutes by 100%. During 60 minutes of operation, while 62.91% of TN, 87.8% of oil-grease were removed, sulphate was removed at the rate of 54.78%. In the studies, 1st and 2nd order kinetic equations for COD removal were examined and it was determined that removal kinetic is more suitable for 2nd order kinetics.

  AtıfScopus7·WoS4

  İncele
• MakaleAçık Erişim2022/r/bayburt/16640
  Elektrokoagülasyon yöntemi ile demir elektrotlar kullanılarak sulardan fosfat giderimi üzerine destek elektrolit türü ve konsantrasyonunun etkisi

  Kul, Sinan; İrdemez, Şahset; Torun, Fatma Ekmekyapar; Reçber, Züleyha; Demircioğlu, Nuhi

  Bu çalışmada elektrokoagülasyon prosesi kullanılarak atıksuyun iletkenliğini artırmak için suya verilen destek elektrolitin türü ve konsantrasyonunun sulardan fosfat giderimine etkisi araştırılmıştır. Ayrıca elektrolitsiz deneyler yapılmış ve sonuçlar karşılaştırılmıştır. Destek elektrolit tipi ve konsantrasyonunun fosfat giderme verimliliği, enerji tüketimi ve reaksiyon hızı üzerindeki etkisi analiz edilmiştir. Deneyler, elektrolit kullanımının fosfat giderme verimliliği üzerinde önemli bir etkisi olmadığını göstermiştir. Ancak elektrolit ilavesinin enerji tüketimini azalttığı ve uzaklaştırma oranını arttırdığı bulunmuştur. Elde edilen sonuçlardan en uygun elektrolit türü olarak NaCl ve optimum doz olarak 5 mM elektrolitin yeterli olduğu belirlenmiştir. Bu koşullar altında, 0.5 mA cm-2 akım yoğunluğunda 100 mg L^-1 PO_4-P için fosfat giderme verimi %96.98, enerji tüketimi 1.13 kWh m^-3 ve birinci dereceden reaksiyon hızı sabiti 0.0593 dk^-1 olarak elde edilmiştir.

  • 
  • 
  AtıfOpenAlex2

  İncele
• MakaleAçık Erişim2021Scopus SJRQ4/r/bayburt/13489
  The effect of pH on removal of phosphate from water using aluminum electrodes by electrocoagulation method; [Alüminyum elektrotlar kullanılarak elektrokoagülasyon yöntemi ile sulardan fosfat gideriminde pH'ın etkisi]

  İrdemez, Şahset; Bingül, Züleyha; Kul, Sinan; Ekmekyapar Torun, Fatma; Demircioğlu, Nuhi

  In this study, the effect of wastewater pH on phosphate removal by electrocoagulation method using aluminum plate electrodes was investigated. For this purpose, experiments were carried out at initial pH values ranging from 3-10, and the effect of the initial pH of the wastewater on phosphate removal efficiency, energy consumption and reaction rate was analyzed. From the results obtained, it was determined that the initial pHs of the optimum wastewater was 3 and 4. Because at low pH, both phosphate removal efficiency is high and the energy consumption of the system is low. While 97% removal efficiency is reached in 20 minutes at pHi=3, it increases in this period with the increase of the wastewater initial pH. These data show that the removal rate is higher at lower initial pHs. While the 1st degree reaction rate constant at pHi=3 is k1=0.2154 min-1, this value decreases to k1=0.071 min-1 at pHi=10. At pHi=3, the energy consumption of the system has been determined as 0.553 kWh m-3 in 12 minutes of contact time. In addition, in the measurements made during the trials, it was observed that the highest PO4-P removal occurred during the period when the pH of the system was between 5-7.

  • 
  • 
  AtıfScopus4·OpenAlex1

  İncele