Sürdürülebilir Kalkınma Amaçları
Yayınlar
- MakaleAçık Erişim2021Scopus SJRQ13D-graphene-laser patterned p-type silicon Schottky diode
Orhan, Elif Oz; Efil, Esra; Bayram, Ozkan; Kaymak, Nuriye; Berberoğlu, Halil; Candemir, Ozun; Pavlov, Ihor; Ocak, Sema Bilge
The influence of the laser patterning (LP) process on the quality of graphene (Gr) film and Schottky diode characteristics was researched in this study. First of all, p-type silicon (Si) was patterned by homemade femtosecond laser source. To compare the resulting effect, non-patterned n-Si and p-Si were used as substrates. To achieve vertically oriented three-dimensional (3D) Gr nanosheets (VGNs) onto the laser patterned p-type Si, non-patterned n-Si, and p-Si substrates, we used Radio-Frequency Plasma Enhanced Chemical Vapor Deposition (RF-PECVD) technique. Then, Raman analyses for VGNs obtained on patterned and non-patterned p-Si and n-Si substrates were conducted. All results indicate that the Gr obtained on all substrates is vertically oriented. Scanning electron microscopy (SEM) analyses were also performed to obtain information about the morphological properties of the 3D Gr structure. In addition, the influence of the laser patterning at the Gr-Si interface was evaluated by comparing two sets of devices which are junctions of Gr-Laser Patterned Si (Gr-LPSi) and Gr-Insulator-Silicon (Gr-I-Si) at 300 K in the dark medium. D1 device consists of a Gr-LPSi junction that involves RF-PECVD grown Gr on the silicon, whose surface exposed the laser beam for patterning. D2 device consists of a Gr-I-Si junction that involves RF-PECVD grown Gr onto the silicon, whose surface involves a thin native oxide layer (~2 nm). The results show that the laser treatment causes an increment in Schottky barrier height (SBH) and decreases leakage currents under a reverse bias voltage of the diode. Notably, we have seen the influence of the laser patterning process on 3D Gr nano-sheets which is that the entire surface of the substrate has now reformed new structures in the nano-sphere and nano-rose morphology, so we believe that this is the first work that shows these structures in this form.
AtıfScopus14WoS13OpenAlex13
İncele - MakaleYalnız künye2020Scopus SJRQ1Current–voltage analyses of Graphene-based structure onto Al2O3/p-Si using various methods
Efil, Esra; Kaymak, Nuriye; Seven, Elanur; Orhan, Elif Oz; Bayram, Ozkan; Ocak, Sema Bilge; Tataroglu, Adem
The present study's main purpose is to determine the current-voltage (I–V) performance of Graphene (Gr) based hetero nanostructure produced on Al2O3/p-Si. Graphene synthesis was carried out using the chemical vapor deposition (CVD) technique on Copper (Cu) foils used as a metal catalyst and transferred onto Al2O3/p-Si using the conventional transfer method. The I–V characteristics of this structure were measured in the dark environment, and the electrical properties of the Gr/Si structure were characterized at room temperature. The rectifying ratio (RR) of the structure was found to be about 103 at ± 3 V. The electrical properties of ideality factor (n), series resistance (Rs), and barrier height (Φb) were examined by using the theory of Thermionic Emission (TE), Norde's method, and Cheung's method. The values of Φb, which were calculated using Norde's method, Cheung's method, and the theory of thermionic emission (TE), were found to be 0.69 eV, 0.71 eV, and 0.68 eV, respectively. The ideality factor was found to be approximately 3.89 according to the theory of TE. The values of series resistance were also determined using the Norde's method and Cheung's two different parameters (dV/dln(I) and H(I)) found to be 9.60 kΩ, 9.12 kΩ, and 5.94 kΩ, respectively.
AtıfScopus25WoS25OpenAlex26İncele