Sürdürülebilir Kalkınma Amaçları

• 1
• 1

• MakaleYalnız künye2021Scopus SJRQ1/r/bayburt/12050
  Frictionless contact mechanics of an orthotropic coating/isotropic substrate system

  Öner, Erdal

  This study has been performed to investigate the receding contact problem of a homogeneous orthotropic coating that is not bonded to a homogeneous isotropic substrate without any interfacial defects. The isotropic substrate is supported on a Winkler foundation. The problem is solved assuming that the contact between the rigid punch and orthotropic coating, and that between the orthotropic coating and isotropic substrate, are frictionless. Additionally, the effect of the body forces is neglected, and only compressive normal tractions can be transmitted through the interfaces. The contact analysis of the orthotropic coating, which is subjected to a contact load using a rigid cylindrical punch, is performed under plane strain conditions. The governing equations are analytically found using the theory of elasticity and Fourier integral transformation techniques. Subsequently, the governing equations are reduced to a system of two singular equations, wherein the unknowns are the contact stresses and contact widths. To numerically solve the resulting singular integral equations, Gauss-Chebyshev integration formulas are employed. It is analyzed the influence of the following parameters on the contact stresses and contact widths: orthotropic-material properties, punch radius, load ratio, Winkler foundation stiffness.

  AtıfScopus26·WoS26·OpenAlex10

  İncele
• MakaleYalnız künye2021Scopus SJRQ1/r/bayburt/12048
  Investigation of continuous and discontinuous contact cases in the contact mechanics of graded materials using analytical method and FEM

  Yaylacı, Murat; Adıyaman, Gökhan; Öner, Erdal; Birinci, Ahmet

  The aim of this paper was to examine the continuous and discontinuous contact problems between the functionally graded (FG) layer pressed with a uniformly distributed load and homogeneous half plane using an analytical method and FEM. The FG layer is made of non-homogeneous material with an isotropic stress–strain law with exponentially varying properties. It is assumed that the contact at the FG layer-half plane interface is frictionless, and only the normal tractions can be transmitted along the contacted regions. The body force of the FG layer is considered in the study. The FG layer was positioned on the homogeneous half plane without any bonds. Thus, if the external load was smaller than a certain critical value, the contact between the FG layer and half plane would be continuous. However, when the external load exceeded the critical value, there was a separation between the FG layer and half plane on the finite region, as discontinuous contact. Therefore, there have been some steps taken in this study. Firstly, an analytical solution for continuous and discontinuous contact cases of the problem has been realized using the theory of elasticity and Fourier integral transform techniques. Then, the problem modeled and two-dimensional analysis was carried out by using ANSYS package program based on FEM. Numerical results for initial separation distance and contact stress distributions between the FG layer and homogeneous half plane for continuous contact case; the start and end points of separation and contact stress distributions between the FG layer and homogeneous half plane for discontinuous contact case were provided for various dimensionless quantities including material inhomogeneity, distributed load width, the shear module ratio and load factor for both methods. The results obtained using FEM were compared with the results found using analytical formulation. It was found that the results obtained from analytical formulation were in perfect agreement with the FEM study.

  AtıfScopus78·WoS78·OpenAlex21

  İncele
• MakaleYalnız künye2018Scopus SJRQ2/r/bayburt/12578
  X-ray CT monitoring of macro void development in mortars exposed to sulfate attack

  Tekin, Ilker; Birgul, Recep; Aruntas, Huseyin Y.

  This study reports the results of nondestructive monitoring of macro void developments in mortars manufactured with both ordinary Portland cement and sulfate resistant cement. Two types of curing were utilized; tap water curing and another curing environment that contains 5% Na2(SO4) solution. Being the primary objective of this study, macro void developments of the mortar specimens were monitored by X-ray Medical Computerized Tomography. Compressive strength tests and water absorption tests were conducted on specimens that were kept in both curing environments for a duration of 560 days. Data analyses yielded consistent results among the three tests used in this experimental study. Macro void ratios of mortars decreased at the beginning of experiments for a certain period; afterwards, macro void ratios increased. The objective of this study was accomplished as anticipated since X-CT image analysis was able to nondestructively monitor macro void development process in cement mortars.

  AtıfScopus6·WoS6·OpenAlex1

  İncele
• BildiriAçık Erişim2011Scopus SJRQ2/r/bayburt/13953
  Site-response effects on RC buildings isolated by triple concave friction pendulum bearings

  Ates, Sevket; Yurdakul, Muhammet

  The main object of this study is to evaluate the seismic response effects on a reinforced concrete building isolated by triple concave friction pendulum (TCFP) bearings. The site-response effects arise from the difference in the local soil conditions at the support points of the buildings. The local soil conditions are, therefore, considered as soft, medium and firm; separately. The results on the responses of the isolated building are compared with those of the non-isolated. The building model used in the time history analysis, which is a two-dimensional and eight-storey reinforced concrete building with and without the seismic isolation bearings and/or the local soil conditions, is composed of two-dimensional moment resisting frames for superstructure and of plane elements featuring plane-stress for substructure. The TCFP bearings for isolating the building are modelled as of a series arrangement of the three single concave friction pendulum (SCFP) bearings. In order to investigate the efficiency of both the seismic isolation bearings and the site-response effects on the buildings, the time history analyses are elaborately conducted. It is noted that the site-response effects are important for the isolated building constructed on soft, medium or firm type local foundation soil. The results of the analysis demonstrate that the siteresponse has significant effects on the response values of the structure-seismic isolation-foundation soil system.

  • 
  • 
  AtıfScopus9·OpenAlex7

  İncele